All 81 services

Turnkey rooftop installation for homes, from structure to commissioning and handover.

Rooftop and ground-mount builds for shops, offices and plazas with commercial-grade protection.

High-capacity installations for factories and mills, engineered around load profile and shift timing.

Battery-backed systems for locations with no grid connection or unusable supply.

Grid plus battery, so load shedding never takes the site offline.

Grid-tied system sized for your bill and prepared for net metering approval.

Add capacity to an existing array without disturbing the working system.

Careful dismantling, transport and reinstallation when you move premises.

Full wash with soft brushes and deionised water to lift baked-on dust without scratching glass.

Dry rotary-brush cleaning for water-scarce sites and areas under water restrictions.

Targeted removal of droppings that create permanent hotspots if left to bake on.

Clears moss, algae and caked dust from frames, gaps and drainage channels.

Seasonal clearing of leaves, sand and construction dust from the array and walkways.

Scheduled inspection, torque check, cleaning and performance log in one visit.

Year-round cover: scheduled cleaning, inspections, priority response and reporting.

Four visits a year, matched to Pakistan's dust and monsoon cycle.

Homeowner package: clean, inspect, test and report in a single appointment.

Multi-string commercial servicing with downtime planned around business hours.

Perimeter mesh that stops pigeons nesting under the array and fouling the modules.

Realigns tilt and azimuth to the season so the array captures its designed irradiance.

End-to-end walkthrough of modules, wiring, inverter, earthing and protection devices.

Scored audit of the whole system with a written report and a prioritised action list.

Measures real output against the design estimate to quantify exactly what you are losing.

Traces each string's current-voltage curve to expose mismatch, shading and degradation.

Infrared sweep that finds heat signatures long before they become visible failures.

Pinpoints cells running hot from cracks, soiling or bypass diode failure.

String-by-string voltage and current comparison to isolate the underperforming run.

Baseline electrical measurements across DC and AC sides with recorded results.

Measures earth electrode resistance against the standard and documents the reading.

Megger testing of DC cabling to catch moisture ingress and damaged insulation.

Aerial thermal survey that covers large rooftops in a fraction of the walking time.

No-cost visit to measure roof area, shading and load before you commit to anything.

A written snapshot of how your system is actually performing, at no charge.

Junction box, bypass diode and frame repairs that avoid a full module replacement.

Fault diagnosis, board-level repair, firmware update and cooling service.

Capacity test on every cell, with like-for-like replacement of the failed unit.

Replaces burnt or loose DC connectors, the most common cause of string dropout.

Re-runs damaged or undersized DC and AC cable in UV-rated conduit.

String fuse replacement with the correct rating and a check of what blew it.

Replaces spent surge arrestors so the next strike does not reach your inverter.

Reseals and rewires module junction boxes showing arcing or water ingress.

Rebuilds combiner terminations, fuses and busbars to remove hotspots and arc risk.

Full cable route inspection with repair of chafed, rodent-damaged or sun-baked runs.

Torque check and retermination across DC, AC and earth connections.

Same-day dispatch when the system is down and you are back on full grid billing.

Guaranteed same-day attendance and repair where parts are in stock.

New earth pit and bonding to bring the installation up to standard.

Verifies earthing continuity, bonding and enclosure safety with a signed record.

Air terminals, down conductors and surge protection sized for the array.

Checks DC isolation, cable routing and fire-path clearance around the array.

Formal audit of the electrical installation with a compliance report you can file.

Recalculates and resets tilt for your latitude and season to lift annual yield.

Tunes string configuration, MPPT settings and cleaning cycle around measured losses.

Breaks total loss into soiling, shading, mismatch, temperature and downtime.

Maps year-round shading from trees, parapets and neighbouring buildings.

Adds capacity, modern modules or a smarter inverter to an ageing system.

Swaps failed or heavily degraded modules with matched replacements.

Replaces an obsolete inverter with a higher-efficiency, monitored unit.

Connects your inverter to a phone app so you can see generation live.

Adds an EV charge point that runs off your own solar generation.

We prepare the file, coordinate the DISCO inspection and follow up until the meter is installed.

Evidence pack and manufacturer follow-up so a valid claim actually gets paid.

Independent condition report in the format insurers accept.

Signed technical documentation for banks, buyers, insurers or regulators.

Long-horizon monitoring with annual degradation reporting against the warranty curve.

Shift-aware servicing for manufacturing roofs where downtime is expensive.

Servicing scheduled around teaching hours and clinical load, with strict safety control.

Tubewell and agri systems, including pump controller and dust-heavy site care.

Large-span roof servicing with proper access and fall protection.

Round-the-clock hotline with a contracted response window.

Load study, array layout, string design and single-line diagram.

Full supply and installation quoted on a straight per-watt basis.

Tier-1 modules supplied with full warranty documentation.

String or hybrid inverter supply matched to the array and the load.

Hot-dip galvanised or aluminium structure engineered for local wind load.

UV-rated DC cable, MC4 terminations and conduit.

AC cabling, breakers and distribution from inverter to main board.

Earth pit, bonding and lightning arrestor provision.

Application, drawings, DISCO liaison and meter commissioning.

Pre-energisation testing, commissioning report and system handover.

Single-contract delivery of the whole project, one accountable party.